Fortinet Document Library

Version:

Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

CLI Reference

diagnose hardware deviceinfo

Use this command to display hardware information that might be useful in debugging.

Syntax

diagnose hardware {get|set} deviceinfo nic [<port>] <Enter>

diagnose hardware {get|set} deviceinfo nic-detail [<port>] <Enter>

nic

Displays port settings. If you do not specify a port and press Enter, the command displays output for all ports.

nic-detail

Displays detailed port settings and statistics. If you do not specify a port and press Enter, the command displays output for all ports.

Example

FortiADC-VM # diagnose hardware get deviceinfo ?

nic display network interface controller status

nic-detail display detailed network interface controller status

 

FortiADC-VM # diagnose hardware get deviceinfo nic-detail port1

Interface: port1

driver: vmxnet3

version: 1.1.29.0-k-NAPI

firmware-version:

bus-info: 0000:03:00.0

supports-statistics: yes

supports-test: no

supports-eeprom-access: no

supports-register-dump: yes

supports-priv-flags: no

 

Settings for port1:

Supported ports: [ TP ]

Supported link modes: 1000baseT/Full

10000baseT/Full

Supported pause frame use: No

Supports auto-negotiation: No

Advertised link modes: Not reported

Advertised pause frame use: No

Advertised auto-negotiation: No

Speed: 10000Mb/s

Duplex: Full

Port: Twisted Pair

PHYAD: 0

Transceiver: internal

Auto-negotiation: off

MDI-X: Unknown

Supports Wake-on: uag

Wake-on: d

Link detected: yes

 

Pause parameters for port1:

Cannot get device pause settings: Operation not supported

Inter-| Receive | Transmit

face |bytes packets errs drop fifo frame compressed multicast|bytes packe ts errs drop fifo colls carrier compressed

port10: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

 

diagnose hardware deviceinfo

Use this command to display hardware information that might be useful in debugging.

Syntax

diagnose hardware {get|set} deviceinfo nic [<port>] <Enter>

diagnose hardware {get|set} deviceinfo nic-detail [<port>] <Enter>

nic

Displays port settings. If you do not specify a port and press Enter, the command displays output for all ports.

nic-detail

Displays detailed port settings and statistics. If you do not specify a port and press Enter, the command displays output for all ports.

Example

FortiADC-VM # diagnose hardware get deviceinfo ?

nic display network interface controller status

nic-detail display detailed network interface controller status

 

FortiADC-VM # diagnose hardware get deviceinfo nic-detail port1

Interface: port1

driver: vmxnet3

version: 1.1.29.0-k-NAPI

firmware-version:

bus-info: 0000:03:00.0

supports-statistics: yes

supports-test: no

supports-eeprom-access: no

supports-register-dump: yes

supports-priv-flags: no

 

Settings for port1:

Supported ports: [ TP ]

Supported link modes: 1000baseT/Full

10000baseT/Full

Supported pause frame use: No

Supports auto-negotiation: No

Advertised link modes: Not reported

Advertised pause frame use: No

Advertised auto-negotiation: No

Speed: 10000Mb/s

Duplex: Full

Port: Twisted Pair

PHYAD: 0

Transceiver: internal

Auto-negotiation: off

MDI-X: Unknown

Supports Wake-on: uag

Wake-on: d

Link detected: yes

 

Pause parameters for port1:

Cannot get device pause settings: Operation not supported

Inter-| Receive | Transmit

face |bytes packets errs drop fifo frame compressed multicast|bytes packe ts errs drop fifo colls carrier compressed

port10: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0