Fortinet Document Library

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:

Version:


Table of Contents

Administration Guide

Configuring HA options

To configure HA options go to System Settings > HA and configure FortiAnalyzer units to create an HA cluster or change cluster configuration.

In System Settings > HA, use the Settings pane to create or change HA configuration, and use the Monitor pane to monitor HA status.

To configure a cluster, set the Operation Mode of the primary unit to High Availability. Then add the IP addresses and serial numbers of each backup unit to primary unit peer list. The IP address and serial number of the primary unit and all backup units must be added to each backup unit's HA configuration. The primary unit and all backup units must have the same Group Name, Group ID and Password.

You can connect to the primary unit GUI to work with FortiAnalyzer. Using configuration synchronization, you can configure and work with the cluster in the same way as you would work with a standalone FortiAnalyzer unit.

Configure the following settings:

 

Operation Mode

Select High Availability to configure the FortiAnalyzer unit for HA.

Select Standalone to stop operating in HA mode.

Cluster Virtual IP

 

Interface

The interface the FortiAnalyzer HA unit uses to provide redundancy.

 

IP Address

The IP address for which the FortiAnalyzer HA unit is to provide redundancy.

Cluster Settings

 

Peer IP

Type the IP address of another FortiAnalyzer unit in the cluster.

 

Peer SN

Type the serial number of the FortiAnalyzer unit corresponding to the entered IP address.

 

Group Name

Type a group name that uniquely identifies the FortiAnalyzer HA cluster. All units in a cluster must have the same Group Name, Group ID and Password.

 

Group ID

Type a group ID from 1 to 255 that uniquely identifies the FortiAnalyzer HA cluster.

 

Password

A password for the HA cluster. All members of the HA cluster must have the same password.

 

Heart Beat Interval

The time the primary unit waits between sending heartbeat packets, in seconds. The heartbeat interval is also the amount of time that backup units waits before expecting to receive a heartbeat packet from the primary unit.

 

Priority

The priority or seniority of the backup unit in the cluster.

 

Initial Sync

To add a backup unit to an HA cluster, turn on this option so that logs are synchronized between the primary and backup units. For more information, see Log synchronization.

 

Log Data Sync

This option is on by default. It provides real-time log synchronization among cluster members after the initial log synchronization.

Configuring HA options

To configure HA options go to System Settings > HA and configure FortiAnalyzer units to create an HA cluster or change cluster configuration.

In System Settings > HA, use the Settings pane to create or change HA configuration, and use the Monitor pane to monitor HA status.

To configure a cluster, set the Operation Mode of the primary unit to High Availability. Then add the IP addresses and serial numbers of each backup unit to primary unit peer list. The IP address and serial number of the primary unit and all backup units must be added to each backup unit's HA configuration. The primary unit and all backup units must have the same Group Name, Group ID and Password.

You can connect to the primary unit GUI to work with FortiAnalyzer. Using configuration synchronization, you can configure and work with the cluster in the same way as you would work with a standalone FortiAnalyzer unit.

Configure the following settings:

 

Operation Mode

Select High Availability to configure the FortiAnalyzer unit for HA.

Select Standalone to stop operating in HA mode.

Cluster Virtual IP

 

Interface

The interface the FortiAnalyzer HA unit uses to provide redundancy.

 

IP Address

The IP address for which the FortiAnalyzer HA unit is to provide redundancy.

Cluster Settings

 

Peer IP

Type the IP address of another FortiAnalyzer unit in the cluster.

 

Peer SN

Type the serial number of the FortiAnalyzer unit corresponding to the entered IP address.

 

Group Name

Type a group name that uniquely identifies the FortiAnalyzer HA cluster. All units in a cluster must have the same Group Name, Group ID and Password.

 

Group ID

Type a group ID from 1 to 255 that uniquely identifies the FortiAnalyzer HA cluster.

 

Password

A password for the HA cluster. All members of the HA cluster must have the same password.

 

Heart Beat Interval

The time the primary unit waits between sending heartbeat packets, in seconds. The heartbeat interval is also the amount of time that backup units waits before expecting to receive a heartbeat packet from the primary unit.

 

Priority

The priority or seniority of the backup unit in the cluster.

 

Initial Sync

To add a backup unit to an HA cluster, turn on this option so that logs are synchronized between the primary and backup units. For more information, see Log synchronization.

 

Log Data Sync

This option is on by default. It provides real-time log synchronization among cluster members after the initial log synchronization.