FortiAuthenticator units listen for requests from authentication clients and can poll Windows AD servers.
- Go to Fortinet SSO Methods > SSO > General to open the Edit SSO Configuration window. The Edit SSO Configuration window contains sections for FortiGate, FSSO, and user group membership.
- In the FortiGate section, configure the following settings:
- In the Fortinet Single Sign-On (FSSO) section, configure the following settings:
Maximum concurrent user sessions
Select Configure Per User/Group to configure the maximum number of concurrent sessions for each user or group. See Fine-grained controls.
Select Download all logs to download all FSSO logs to your management computer.
Enable Windows event log polling (e.g. domain controllers/Exchange servers)
Select Configure Events to select the Windows security event IDs to use in event log polling. Select from event IDs 528, 540, 672, 673, 674, 680, 4624, 4768, 4769, 4770, and 4776.
Enable DNS lookup to get IP from workstation name Select to use DNS lookup to get IP address information when an event contains only the workstation name. This option is enabled by default. Directly use domain DNS suffix in lookup Select to use the domain DNS suffix when doing a DNS lookup. This option is disabled by default. Enable reverse DNS lookup to get workstation name from IP Select to enable reverse DNS lookup. Reverse DNS lookup is used when an event contains only an IP address and no workstation name. This option is enabled by default. Do one more DNS lookup to get full list of IPs after reverse lookup of workstation name Reverse DNS lookup is used when an event contains only an IP address and no workstation name. After the workstation name is determined, it is used in the DNS lookup again to get more complete IP address information. This is useful in environments where workstations have multiple network interfaces. This option is disabled by default. Include account name ending with $ (usually computer account) Accounts that end in "$" used to exclusively denote computer accounts with no actual user, but in some cases, valid accounts imported from dated systems can feature them. This option is disabled by default.
Enable FortiNAC SSO
Select to enable the retrieval of SSO sessions from FortiNAC sources.
Select Edit to choose one or more configured FortiNAC sources to use as SSO sources.
Select Configure FortiNACs to configure FortiNAC sources (under System > Administration > FortiNACs). For more information, see FortiNACs.
Enable Radius Accounting SSO clients Select to enable the detection of users sign-ons and sign-offs from incoming RADIUS accounting (Start, Stop, and Interim-Update) records. Enable Syslog SSO Select to enable Syslog SSO, and configure syslog sources. Enable FortiClient SSO Mobility Agent Service Select to enable single sign-on (SSO) by clients running FortiClient Endpoint Security. For more information, see FortiClient SSO Mobility Agent. FortiClient listening port Enter the FortiClient listening port number. Enable authentication Select to enable authentication, then enter a secret key, or password, in the Secret key field. Keep-alive interval Enter the duration between keep-alive transmissions, from 1 to 60 minutes. Default is 5 minutes. Idle timeout Enter an amount of time in minutes after which to logoff a user if their status is not updated. The value cannot be lower than the Keep-alive interval value. Enable NTLM
Select to enable the NT LAN Manager (NTLM) to allow logon of users who are connected to a domain that does not have the FSSO DC Agent installed. Disable NTLM authentication only if your network does not support NTLM authentication for security or other reasons.
Enable hierarchical FSSO tiering Select to enable hierarchical FSSO tiering. Enter the collector listening port in the Collector listening port field. Enable DC/TS Agent Clients
Select to enable clients using DC or TS Agent. Enter the UDP port in the DC/TS Agent listening port field. Default is 8002.
Require authentication for TS agents (disables DC agent support)
Select to require authentication, then enter a secret key, or password, in the Secret key field.
Enable DNS lookup to get IP from workstation name
Select to use DNS lookup to get IP address information when a client contains only the workstation name. This option is enabled by default.
FortiAuthenticator attempts to obtain the workstation IP address using DNS lookup if the logon request contains only the workstation name. If the initial lookup fails, FortiAuthenticator will retry every 10 seconds for the following 5 minutes.
Ignore workstation name that is not full DNS name
Select if the DNS server does not support a workstation name that is not a full DNS name, otherwise service delay may occur. This option is enabled by default.
Enable reverse DNS lookup to get workstation name from IP
Select to enable reverse DNS lookup. Reverse DNS lookup is used when a client contains only an IP address and no workstation name. This option is enabled by default.
Restrict auto-discovered domain controllers to configured Windows event log sources and remote LDAP servers Select to enable restricting automatically discovered domain controllers to already configured domain controllers only. See Windows event log sources. Enable Windows Active Directory workstation IP verification
Select to enable workstation IP verification with Windows Active Directory.
If enabled, select Enable IP change detection via DNS lookup to detect IP changes via DNS lookup.
Disable NTLMv1 in client authentication to Windows AD server Optionally, disable NTLMv1, as NTLMv2 is supported.
Disable SMB1 in client connection to Windows AD server
Optionally, disable SMB1.
- In the User Group Membership section, configure the following settings:
- Select OK to apply the settings.
Each FortiGate unit that will use FortiAuthenticator to provide Single Sign-On authentication must be configured to use FortiAuthenticator as an SSO server.
- On the FortiGate unit, go to Security Fabric > External Connectors and select Create New.
- Select FSSO Agent on Windows AD.
- Enter a name for FortiAuthenticator in the Name field.
- In the Primary FSSO agent field, enter the IP address of FortiAuthenticator.
- In the Password field, enter the secret key that you defined for FortiAuthenticator. See Enable authentication.
- Select OK.
In a few minutes, the FortiGate unit receives a list of user groups from FortiAuthenticator. When you open the server, you can see the list of groups. The groups can be used in identity-based security policies.