SD-WAN rules - maximize bandwidth (SLA)

SD-WAN rules are used to control how sessions are distributed to SD-WAN members. Rules can be configured in one of five modes:

• auto: Interfaces are assigned a priority based on quality.
• Manual (manual): Interfaces are manually assigned a priority.
• Best Quality (priority): Interface are assigned a priority based on the link-cost-factor of the interface. See SD-WAN rules - best quality.
• Lowest Cost (SLA) (sla): Interfaces are assigned a priority based on selected SLA settings. See SD-WAN rules - lowest cost (SLA).
• Maximize Bandwidth (SLA) (load-balance): Traffic is distributed among all available links based on the selected load balancing algorithm.

When using Maximize Bandwidth mode (load-balance in the CLI), SD-WAN will all of the links that satisfies SLA to forward traffic based on a round‑robin load balancing algorithm.

ADVPN is not supported in this mode.

In this example, your wan1 and wan2 SD-WAN interfaces connect to two ISPs that both go to the public internet. You want to configure Gmail services to use both of the interface, but the link quality must meet a standard of latency: 10ms, and jitter: 5ms. This can maximize the bandwidth usage.

To configure an SD-WAN rule to use Maximize Bandwidth (SLA):

1. On the FortiGate, add wan1 and wan2 as SD-WAN members, then add a policy and static route. See SD-WAN quick start for details.
2. Create a new Performance SLA named google that includes an SLA Target 1 with Latency threshold = 10ms and Jitter threshold = 5ms. See Performance SLA - link monitoring.
3. Go to Network > SD-WAN Rules.
4. Click Create New. The Priority Rule page opens.
5. Enter a name for the rule, such as gmail.
6. Configure the following settings:

   

   Field	Setting
   Internet Service	Google-Gmail
   Strategy	Maximize Bandwidth (SLA)
   Interface preference	wan1 and wan2
   Required SLA target	google (created in step 2).

7. Click OK to create the rule.

To configure an SD-WAN rule to use SLA:

config system sdwan
    config health-check
        edit "google"
            set server "google.com"
            set members 1 2
            config sla
                edit 1
                    set latency-threshold 10
                    set jitter-threshold 5
                next
            end
        next
    end
    config service
        edit 1
            set name "gmail"
            set mode load-balance
            set internet-service enable
            set internet-service-id 65646
            config sla
                edit "google"
                    set id 1
                next
            end
            set priority-members 1 2
        next
    end
end

To diagnose the performance SLA status:

FGT # diagnose sys sdwan health-check google
Health Check(google):
Seq(1): state(alive), packet-loss(0.000%) latency(14.563), jitter(4.334) sla_map=0x0
Seq(2): state(alive), packet-loss(0.000%) latency(12.633), jitter(6.265) sla_map=0x0

FGT # diagnose sys sdwan service 1
Service(1): Address Mode(IPV4) flags=0x0

    TOS(0x0/0x0), Protocol(0: 1->65535), Mode(load-balance)
    Members:<<BR>>

        1: Seq_num(1), alive, sla(0x1), num of pass(1), selected
        2: Seq_num(2), alive, sla(0x1), num of pass(1), selected

    Internet Service: Google.Gmail(65646)

When both wan1 and wan2 meet the SLA requirements, Gmail traffic will use both wan1 and wan2. If only one of the interfaces meets the SLA requirements, Gmail traffic will only use that interface.

If neither interface meets the requirements but health-check is still alive, then wan1 and wan2 tie. The traffic will try to balance between wan1 and wan2, using both interfaces to forward traffic.