config wireless-controller timers
Configure CAPWAP timers.
config wireless-controller timers
Description: Configure CAPWAP timers.
set ap-reboot-wait-interval1 {integer}
set ap-reboot-wait-interval2 {integer}
set ap-reboot-wait-time {string}
set auth-timeout {integer}
set ble-scan-report-intv {integer}
set client-idle-rehome-timeout {integer}
set client-idle-timeout {integer}
set discovery-interval {integer}
set drma-interval {integer}
set echo-interval {integer}
set fake-ap-log {integer}
set ipsec-intf-cleanup {integer}
set nat-session-keep-alive {integer}
set radio-stats-interval {integer}
set rogue-ap-cleanup {integer}
set rogue-ap-log {integer}
set sta-capability-interval {integer}
set sta-locate-timer {integer}
set sta-stats-interval {integer}
set vap-stats-interval {integer}
end
config wireless-controller timers
|
Parameter |
Description |
Type |
Size |
Default |
|---|---|---|---|---|
|
ap-reboot-wait-interval1 |
Time in minutes to wait before AP reboots when there is no controller detected. |
integer |
Minimum value: 5 Maximum value: 65535 |
0 |
|
ap-reboot-wait-interval2 |
Time in minutes to wait before AP reboots when there is no controller detected and standalone SSIDs are pushed to the AP in the previous session. |
integer |
Minimum value: 5 Maximum value: 65535 |
0 |
|
ap-reboot-wait-time |
Time to reboot the AP when there is no controller detected and standalone SSIDs are pushed to the AP in the previous session, format hh:mm. |
string |
Maximum length: 7 |
|
|
auth-timeout |
Time after which a client is considered failed in RADIUS authentication and times out. |
integer |
Minimum value: 5 Maximum value: 30 |
5 |
|
ble-scan-report-intv |
Time between running Bluetooth Low Energy. |
integer |
Minimum value: 10 Maximum value: 3600 |
30 |
|
client-idle-rehome-timeout |
Time after which a client is considered idle and disconnected from the home controller. |
integer |
Minimum value: 2 Maximum value: 3600 |
20 |
|
client-idle-timeout |
Time after which a client is considered idle and times out. |
integer |
Minimum value: 20 Maximum value: 3600 |
300 |
|
discovery-interval |
Time between discovery requests. |
integer |
Minimum value: 2 Maximum value: 180 |
5 |
|
drma-interval |
Dynamic radio mode assignment. |
integer |
Minimum value: 1 Maximum value: 1440 |
60 |
|
echo-interval |
Time between echo requests sent by the managed WTP, AP, or FortiAP. |
integer |
Minimum value: 1 Maximum value: 255 |
30 |
|
fake-ap-log |
Time between recording logs about fake APs if periodic fake AP logging is configured. |
integer |
Minimum value: 1 Maximum value: 1440 |
1 |
|
ipsec-intf-cleanup |
Time period to keep IPsec VPN interfaces up after WTP sessions are disconnected. |
integer |
Minimum value: 30 Maximum value: 3600 |
120 |
|
nat-session-keep-alive |
Maximal time in seconds between control requests sent by the managed WTP, AP, or FortiAP. |
integer |
Minimum value: 0 Maximum value: 255 |
0 |
|
radio-stats-interval |
Time between running radio reports. |
integer |
Minimum value: 1 Maximum value: 255 |
15 |
|
rogue-ap-cleanup |
Time period in minutes to keep rogue AP after it is gone. |
integer |
Minimum value: 0 Maximum value: 4294967295 |
0 |
|
rogue-ap-log |
Time between logging rogue AP messages if periodic rogue AP logging is configured. |
integer |
Minimum value: 0 Maximum value: 1440 |
0 |
|
sta-capability-interval |
Time between running station capability reports. |
integer |
Minimum value: 1 Maximum value: 255 |
30 |
|
sta-locate-timer |
Time between running client presence flushes to remove clients that are listed but no longer present. |
integer |
Minimum value: 0 Maximum value: 86400 |
1800 |
|
sta-stats-interval |
Time between running client. |
integer |
Minimum value: 1 Maximum value: 255 |
10 |
|
vap-stats-interval |
Time between running Virtual Access Point. |
integer |
Minimum value: 1 Maximum value: 255 |
15 |