Fortinet black logo

Release Notes

Home FortiSwitch 7.2.3 Release Notes
7.2.3
7.2.7
7.2.6
7.2.5
7.2.4
7.2.3
7.2.2
7.2.1
7.2.0
7.0.10
7.0.9
7.0.8
7.0.7
7.0.6
7.0.5
7.0.4
7.0.3
7.0.2
7.0.1
7.0.0
6.4.14
6.4.13
6.4.12
6.4.11
6.4.10
6.4.9
6.4.8
6.4.7
6.4.6
6.4.5
6.4.4
6.4.3
6.4.2
6.4.1
6.4.0
6.2.8
6.2.7
6.2.6
6.2.5
6.2.4
6.2.3
6.2.2
6.2.1
6.2.0
6.0.7
6.0.6
6.0.5
6.0.4
6.0.3
6.0.2
6.0.1
6.0.0
3.6.12
3.6.11
3.6.10
3.6.9
3.6.8
3.6.7
3.6.6
3.6.5
3.6.4
3.6.3
3.6.2
3.6.1
3.6.0
3.5.6
3.5.5
3.5.4
3.5.3
3.5.2
3.5.1
3.5.0
3.4.3
3.4.2
3.4.1
3.4.0
3.3.3
3.3.2
3.3.1

Resolved issues

Resolved issues

The following issues have been fixed in FortiSwitchOS 7.2.3. For inquiries about a particular bug, please contact Customer Service & Support.

Bug ID Description
806907 Packet loss occurs when using the SP-CABLE-FS-SFP+5 direct-attach cable with FS-124F switches.
818628 When Virtual Router Redundancy Protocol (VRRP) is being used in a layer-3 MCLAG topology, static routes disappear after the FortiSwitch unit is restarted.
833450 Layer-2 multicast traffic is flooding to ports within the same VLAN, even though IGMP snooping is enabled.

833503

The FortiGate device does not detect a standalone FS-224E-POE that is running FortiSwitchOS 7.0.5.
834930 The diagnose switch mclag peer-consistency-check command displays split ports incorrectly.
837168

The following switches make a high fan noise:

  • FS-224D-FPOE

  • FS-224E-POE

  • FS-248D

838908, 861167

The event log erroneously reports “FAN failure detected” on multiple FS-248E-POE switches.
844973 After the firmware is successfully uploaded, the FS-M426E switch fails to upgrade.
845190 FortiSwitchOS will not allow https to be removed from the set allowaccess configuration.
846994 Configuring the set group-name under config match for config user tacacs+ does not work.

849465

Using FN-TRAN-GC with the FS-108E or FS-108F switch causes link flapping or wrongly shows that the link is up when the cable is not connected.

850859

FortiSwitchOS sends the wrong OID for the SNMPv3 trap for link-down events.

857391

After upgrading FortiSwitchOS, multiple FS-448E switches report that the fan has failed, although the fan status is OK.
861492 The mgmt interface MAC address is set to 00:01:02:03:04:05 after a reboot or factory reset.

863009

When running FortiSwitchOS 7.2.2, the RPS LED does not light with the appropriate color when a redundant power supply is inserted.

866231

The set status down command (under config switch physical-port) does not work on the SFP+ ports on the FS-426E-FPOE for certain versions of FortiSwitchOS. If you need to shut down any of the SFP+ ports on the FS-426E-FPOE, do not use FortiSwitchOS 7.0.5, 7.2.0, 7.2.1, or 7.2.2.

Common vulnerabilities and exposures

Visit https://fortiguard.com/psirt for more information.

Bug ID CVE references
855445

FortiSwitchOS 7.2.3 is no longer vulnerable to the following CVE Reference:

  • CVE-2022-3602
Previous
Next

Resolved issues

The following issues have been fixed in FortiSwitchOS 7.2.3. For inquiries about a particular bug, please contact Customer Service & Support.

Bug ID Description
806907 Packet loss occurs when using the SP-CABLE-FS-SFP+5 direct-attach cable with FS-124F switches.
818628 When Virtual Router Redundancy Protocol (VRRP) is being used in a layer-3 MCLAG topology, static routes disappear after the FortiSwitch unit is restarted.
833450 Layer-2 multicast traffic is flooding to ports within the same VLAN, even though IGMP snooping is enabled.

833503

The FortiGate device does not detect a standalone FS-224E-POE that is running FortiSwitchOS 7.0.5.
834930 The diagnose switch mclag peer-consistency-check command displays split ports incorrectly.
837168

The following switches make a high fan noise:

  • FS-224D-FPOE

  • FS-224E-POE

  • FS-248D

838908, 861167

The event log erroneously reports “FAN failure detected” on multiple FS-248E-POE switches.
844973 After the firmware is successfully uploaded, the FS-M426E switch fails to upgrade.
845190 FortiSwitchOS will not allow https to be removed from the set allowaccess configuration.
846994 Configuring the set group-name under config match for config user tacacs+ does not work.

849465

Using FN-TRAN-GC with the FS-108E or FS-108F switch causes link flapping or wrongly shows that the link is up when the cable is not connected.

850859

FortiSwitchOS sends the wrong OID for the SNMPv3 trap for link-down events.

857391

After upgrading FortiSwitchOS, multiple FS-448E switches report that the fan has failed, although the fan status is OK.
861492 The mgmt interface MAC address is set to 00:01:02:03:04:05 after a reboot or factory reset.

863009

When running FortiSwitchOS 7.2.2, the RPS LED does not light with the appropriate color when a redundant power supply is inserted.

866231

The set status down command (under config switch physical-port) does not work on the SFP+ ports on the FS-426E-FPOE for certain versions of FortiSwitchOS. If you need to shut down any of the SFP+ ports on the FS-426E-FPOE, do not use FortiSwitchOS 7.0.5, 7.2.0, 7.2.1, or 7.2.2.

Common vulnerabilities and exposures

Visit https://fortiguard.com/psirt for more information.

Bug ID CVE references
855445

FortiSwitchOS 7.2.3 is no longer vulnerable to the following CVE Reference:

  • CVE-2022-3602
Previous
Next