FortiGate

The following procedures include configuration steps for a typical Security Fabric implementation, where the edge FortiGate is the root FortiGate, and the downstream FortiGate devices are all devices that are downstream from the root FortiGate.

Configure the root FortiGate

The edge FortiGate is typically configured as the root FortiGate, as this allows you to view the full topology of the Security Fabric from the top down.

To configure the root FortiGate:

1. Connect to the root FortiGate and go to Security Fabric > Settings.
2. Enable FortiGate Telemetry.

   FortiAnalyzer Logging is automatically enabled.

   

3. Enter the Group name and select the FortiTelemetry enabled interfaces.
4. In the FortiAnalyzer Logging section, in the IP address field, enter the IP address of the FortiAnalyzer.

   If you select Test Connectivity and this is the first time that you are connecting the FortiGate to the FortiAnalyzer, you will receive a warning message because the FortiGate has not yet been authorized on the FortiAnalyzer. You can configure this authorization when you configure the FortiAnalyzer. See FortiAnalyzer.

5. If you need log transmissions to be encrypted, enable SSL encrypt log transmission.
6. If required, enable Allow access to FortiGate REST API and, optionally, Trust FortiAnalyzer by serial number.

   The FortiGate will verify the FortiAnalyzer by retrieving its serial number and checking it against the FortiAnalyzer certificate. The FortiAnalyzer serial number is stored in the FortiGate configuration. When authorizing the FortiGate on the FortiAnalyzer, the FortiGate admin credentials do not need to be entered. For more information, see Simplify FortiAnalyzer Pairing, in the FortiOS 6.2.0 New Features Guide.

7. Click Apply.

Add downstream devices

Downstream FortiGate devices can be securely added to the Security Fabric without sharing the password of the root FortiGate. Downstream device serial numbers can be authorized from the root FortiGate, or allowed to join by request. New authorization requests include the device serial number, IP address, and HA members. HA members can include up to four serial numbers and is used to ensure that, in the event of a fail over, the secondary FortiGate is still authorized.

Pre-authorizing the downstream FortiGate

When a downstream Fortinet device's serial number is added to the trusted list on the root FortiGate, the device can join the Security Fabric as soon as it connects. After the new device is authorized, connected FortiAP and FortiSwitch devices are automatically included in the topology, where they can be authorized with one click.

To pre-authorize a FortiGate:

1. On the root FortiGate, go to Security Fabric > Settings.
2. Ensure that the interface that connects to the downstream FortiGate has FortiTelemetry enabled.
3. In the Pre-authorized FortiGates, select Edit. Add a new FortiGate to the list using the downstream device's serial number.

   

4. On the downstream FortiGate, go to Security Fabric > Settings.
5. Enable FortiGate Telemetry.

6. Enable Connect to upstream FortiGate.

7. Enter the IP address of the upstream or root FortiGate in the FortiGate IP field.

8. Add the FortiTelemetry enabled interfaces.

9. Click Apply.

10. On the root FortiGate, go to Security Fabric > Settings and verify that the downstream FortiGate that you added appears in the Security Fabric topology.

    

Using LLDP

You can automatically prompt downstream FortiGate devices to join the Security Fabric using Link Layer Discovery Protocol (LLDP) and interface role assignments.

1. On the root FortiGate, assign the LAN role to all interfaces that may connect to downstream FortiGate devices.

   When the LAN role is assigned to an interface, LLDP transmission is enabled by default.

2. When a downstream FortiGate is installed, assign the WAN role to the interface that connects to the upstream FortiGate.

   When the WAN role is assigned, LLDP reception is enabled by default. The newly installed FortiGate uses LLDP to discover the upstream FortiGate, and the administrator is prompted to configure the FortiGate to join the Security Fabric.

3. On the root FortiGate, the new FortiGate must be authorized before it can join the Security Fabric.

If the network contains switches or routers, LLDP may not function as expected because some devices do not pass LLDP packets.

Device request

A device can request to join the Security Fabric from another FortiGate, but it must have the IP address of the root FortiGate. The administrator of the root FortiGate must also authorize the device before it can join the Security Fabric.

The root FortiGate must have FortiTelemetry enabled on the interface that the device connects to.

To enable FortiTelemetry on an interface:

1. Go to Network > Interfaces.
2. Edit the interface that the device that you authorizing to join the Security Fabric is connected to.
3. Under Administrative Access, enable FortiTelemetry.
4. Under Networked Devices, turn on Device Detection.

To join the Security Fabric by device request:

1. Connect to the unauthorized FortiGate or FortiWiFi device, and go to Security Fabric > Settings.
2. Enable FortiGate Telemetry.
3. To connect, enable Connect to upstream FortiGate.
4. Set FortiGate IP to the IP address of the upstream FortiGate.
5. Connect to the root FortiGate and go to Security Fabric > Settings. The new FortiGate appears in the Topology as unauthorized.
6. Click on the unauthorized device and select Authorize to authorize the device.

CLI commands

Use the following commands to view, accept, and deny authorization requests, to view upstream and downstream devices, and to list or test fabric devices:

Command	Description
diagnose sys csf authorization pending-list	View pending authorization requests on the root FortiGate.
diagnose sys csf authorization accept <serial-number-value>	Authorize a device to join the Security Fabric.
diagnose sys csf authorization deny <serial-number-value>	Deny a device from joining the Security Fabric.
diagnose sys csf downstream	Show connected downstream devices.
diagnose sys csf upstream	Show connected upstream devices.
diagnose sys csf fabric-device list	List all known fabric devices.
diagnose sys csf fabric-device test	Test connections to locally configured fabric devices.

Desynchronizing settings

By default, the settings for FortiAnalyzer logging, central management, sandbox inspection, and FortiClient EMS are synchronized between all FortiGate devices in the Security Fabric. To disable the automatic synchronization of these settings, use the following CLI command:

config system csf

set configuration-sync local

end

Deauthorizing a device

A device can be deauthorized to remove it from the Security Fabric.

To deauthorize a device:

1. On the root FortiGate, go to Security Fabric > Settings
2. In the Topology field, click on the device and select Deauthorize.
3. Click on the device.

After devices are deauthorized, the devices' serial numbers are saved in a trusted list that can be viewed in the CLI using the show system csf command. For example, this result shows a deauthorized FortiSwitch:

show system csf

config system csf

set status enable

set group-name "Office-Security-Fabric"

set group-password ENC 1Z2X345V678

config trusted-list

edit "FGT6HD391806070"

next

edit "S248DF3X17000482"

set action deny

next

end

end

end